Slatted Four Post Farmhouse Bed
Slatted Four-Post Farmhouse Bed – King Size Bring strong farmhouse presence to your bedroom with this king-sized four-post bed featuring a bold slatted headboard and footboard. Built on sturdy 4×4 posts, this design delivers architectural impact and modern rustic appeal in equal measure. • Fits a standard 76″ × 80″ king mattress, providing generous proportions and a commanding focal point. • The clean vertical slats in both the headboard and footboard reduce visual heaviness while maintaining sturdy form. • Straightforward materials and construction make it accessible for the DIY builder—perfect for an intermediate project with standout results. • Finish it your way: stain for rich natural warmth, paint for crisp farmhouse style, or mix materials for a two-tone modern twist. Ideal for those looking to create a statement bed that’s both timeless and stylish, with hands-on satisfaction and standout visual impact.
Specifications
| Project type | Beds and Bed Frames |
|---|---|
| Room | Bedroom |
| Style | Cottage Style Furniture Plans |
| Difficulty | Intermediate |
| Estimated cost | $150 - $200 |
Dimensions
Use the size-specific shopping and cut lists below.
Shopping List
- 3 – 2x6 @ 8 feet or stud length
- 3 – 2x10 @ 8 feet
- 2 – 1x12 @ 8 feet
- 4 – 4x4 @ 6 feet
- 2 – 2x3 @ 8 feet
- 1-1/4” and 2-1/2” pocket hole screws
Cut List
- 3 – 2x6 @ 74”
- 1 – 2x10 @ 74”
- 5 – 1x12 @ 23-3/4”
- 5 – 1x12 @ 11-3/4”
- 4 – 4x4 @ 72”
- 2 – 2x10 @ 80”
- 2 – 2x3 @ 80”
- Additional 2x3 supports may be required and/or bed slats depending on box spring
Tools
- measuring tape
- square
- pencil
- safety glasses
- hearing protection
- kreg-jig
- drill
- circular saw
- sander
- countersink drill bit
Step-by-step Instructions
Predrill 1-1/2” pocket holes on each end of 2x6 and 2x10 boards for attaching in step 2.
Build headboard and footboard pieces by drilling 3/4” pocket holes on ends of 1x12s and attaching to the 2x6s and 2x10 with 1-1/4” pocket hole screws. The 1x12s should be centered on the 2x boards. TIP: Use 3/8” plywood as a spacer to help guide placement.
Step 2
Attach to the 4x4 posts through pocket holes drilled in step 1 with 2-1/2” pocket hole screws and wood glue. Center panels on 4x4s so there is a 1” space on either side.
Step 3
Drill three 1-1/2” pocket holes on each end of the 2x10 siderail boards. Attach to the 4x4s, centered on the 4x4s (1” space on each side).
Step 4
Attach cleats to siderails with 2-3/4” screws and glue.
Step 5
Finishing
Sand all surfaces, starting with a medium grit and finishing with fine. Wipe off the dust, fill any holes or gaps with wood filler, and sand smooth once dry. Apply primer if you're painting, then finish with your choice of paint or stain and seal with a durable clear topcoat. For outdoor projects, use exterior-rated primer, paint or stain, and sealer so the piece stands up to the weather.
Source (temporary): https://www.ana-white.com/woodworking-projects/slatted-four-post-farmhouse-bed-standard-king-size-free-plans